URF

Description

Universal RF codes, discussions about the RF subsystem and devices supported.

Forums

Struggling with URFRx

I have been struggling with getting URFRx working for a while.

I have an Arduino nano connected directly to my spare Livebox; it has been loaded with UniversalRFRx.ino. 

If I telnet into the Livebox and monitor microcom -s 57600 /dev/ttyUSB0 I can see the words “starting” and streams of RF data when I send 433 MHz transmissions. 

I have put a valid RF code in the URF Rx rf 1.

I thought I would see a state change in the xFx message viewer, when I transmit and then receive the code in URF Rx rf 1, but all I see is the following.

xap-header

{

v=12

hop=1

uid=FF00EE01

class=xAPBSC.info

source=dbzoo.livebox.urfrx:rf.1

}

input.state

{

state=?

}

I hope I have not missed something glaringly obvious, but I have now exhausted my limited HAH knowledge.

Once I get over this stage I would like to trigger a light when a HE105 door switch is broken. Will concentrate on this once I can see a state change in the xFx.

Any help would be very much appreciated.

Kema…

Forums

Hi Brett,

 

just testing the URF RF with a HAHnode

I've gathered up most libs that seem to be missing, i'm down to the final compile error

any suggestions greatly recieved thanks


In file included from /bsc.h:11,
                 from /urfdecoder.h:13,
                 from genurf.c:14:
xap.h:58: error: expected specifier-qualifier-list before 'time_t'
xap.h:90: error: field 'txAddress' has incomplete type
In file included from /urfdecoder.h:13,
                 from genurf.c:14:
bsc.h:56: error: expected specifier-qualifier-list before 'time_t'

 

Andrew

Forums

I've been working on a standalone piece of hardware that allows you to put a URF Tx unit directly onto your network without being tethered to your livebox.  Part of my push to isolate all this hardware as standalone things which allows us to move the backend software separately to new platforms.  I have URF and Relays separated now.

I ran aground in my testing as I don't have a spare RF Tx unit and I think the one on my HAH unit is broken.  For hardware you can use an Arduino or the base board and the ethernet component of the ethrelay uni (might have to adjust the PIN in the src).  Just plonk on a RF Tx and you are good to go.

The reason for doing this is so because sometimes you don't get the range you need and its just easier to take the Transmitter closer to where you need it !

The source is in the repository and I have patched up all the libraries in there so they compile correctly for the latest IDE, something I had been meaning to do for a while.   http://livebox-hah.googlecode.com/svn/trunk/userapps/arduino/EthURF/

Anyway if somebody verifies this before I get my new RF Tx from HK that would be cool.

Brett

Forums

For those that want to live on the edge.  I've posted beta 309.1 which has my new urf rx module.  This requires you to connect an Arduino with a RF receiever and feed the serial output to the Livebox for interpretation.  It should work on a HAHNode too if you wire it correctly.

There isn't any documenation on how this all works but if you are keen I can get motiviated to get some started, its on my do to list along with overhauling the pachube web page to xively.

I successfully got it to recieve the signal from Byron transmitter and have it decode, in the arduino, and the pulse stream corrected interpretted by the C backend on the Livebox - thus my beta posting.

Teaser of some debug output.

[inf][rfrx.c:101:serialInputHandler] Reset RF decoders
[inf][rfrx.c:85:serialInputHandler] -11248,400,-1056,1136,-336,400,-1056,400,-1056,416,-1056, 
384,-1072,384,-1072,400,-1072,384,-1072,400,-1056,400,-1056,1136,-336,400,-1072,384,-1072,384,
-1072,400,-1072,384,-1072,384,-1072,384,-1088,1120,-336,384,-1088,1120,-352,368,-1088,1120,-352,
368,-10016 [inf][urfdecoder.c:194:URFConsumer] MATCH - rf:2 on [inf][bsc.c:120:bscSetState] state=1 [inf][tx.c:19:xapSend] send xap-header { v=12 hop=1 uid=FF00EE02 class=xAPBSC.event source=dbzoo.livebox.urfrx:rf.2 } input.state { state=on }

There will be a new section which will look something like this and a new WEB tab to create it.

[urfrx]
devices=1
rf1.label=RF 1
rf1.off=0101017A0437046001600101271018401014
rf1.on=010201820436046A015601700436045001700101271018100001820339
enable=1
usbserial=/dev/ttyUSB1

Anyway  early days but it looking promising.

Brett

Forums

Hi all,

I am very new to all this, I have my livebox up & running and wish to control my

Homeasy remote switches, I have a set of HE830s, cos I already had some in

use around the house.

 

Are the on/off codes for this model available? I have asked Homeasy and so far have got nowhere!

If not, should I change to another brand/type?

 

Thanks.

Ken

Forums

Hi

Has anyone managed to successfully control any of the available TRVs ?

My goal is to simply open and close a valve via rf. I don't need feedback.

John

Forums

Just something I've been playing with.  I'm not sure its 100% accurate as I still need to compare what the real waveforms look like vs those I'm plotting from the data.  Anyway have a play see what you think.

/content/rfplot

UPDATE: Sorry about the email spam I didn't know  page node had subscription notifications on by default.