Hardware

Description

Building / testing and troubleshooting the HAH hardware.

Well i got the jeenode so started to play, the problem is the xap-serial is not picking it up (but is running)

This is my config file and the photo shows my putty sessions.

--[[
    JeeNode to xAP Endpoint mapping
--]]

--_DEBUG=1
module(...,package.seeall)

monitor = require("xap.jeenode").monitor
RoomNode = require("xap.roomnode").RoomNode
OutputNode = require("xap.outputnode").OutputNode
IRNode = require("xap.irnode").IRNode

info={
   version="2.0", description="JeeNode"
}

local jeemon={
      port="/dev/ttyUSB0",
      baud=57600,
      stop=1,
      databits=8,
      parity="none",
      flow="none"
}

-- Keyed by NODE ID
local nodes = {
   [2] = RoomNode{base="dbzoo.livebox.1.jeenode:pond", endpoints={temp=1,lobat=0}, ttl=900},
}

function init()
   monitor(jeemon, nodes)
end

 

 

Anyone got any pointers?

Forums

Hi Derek,

Recieved the Long range external antenna from the shop and I was wondering about the best way of 'tweaking' the board to accomodate the connector, alternatively I would prefer to mount the connector to the shell of the Livebox but in doing so I would need to extend the connection from the RF board to the socket - is this advisable?

Thanks

David

Forums

Hi, I recently received my semi new Livebox and HAH PCB. The kit looks good, all packed and labeled very well. The PCB however was of a new design, so it now fits a 1 wire and has the 15v relocated next to the RJ11 gain.
I have been soldering the components on the PCB, the 1 wire on board has not been updated on the wiki. So when done I even restrained my self from hooking it up and truning it on directly, instead I followed the instructios. Hooked up the HAH and measured 5.0 volt no ATMega inserted. When inserted the voltage drops to 4.90V which I guess would be ok.
So now having my HAH board seamingly ok I wanted to test it from the webpage and toggle the relay. So turning it on it takes approx 10 minutes before it becomes online. As I don't have any experience with Liveboxes or HAH I am not sure if this is normal or not. It also does not matter having the HAH board plugged in or left out.
When turning the power on the middle led lights up, than the power led starts blinking while the middle led now and than lights up. By the time the middle led is on almost continuelsy the box goes online. So when I got the box online I toggled the relays, heard clicking sound so this was looking good. At least the Livebox is talking to my HAH board. The 1Wire did show ? no reading. Since the relays were working I assumed the HAH was working ok. Next hooking up the LCD. The LCD does show booting v3.4 but then nothing happens and it remains showing this line. Trying to set the LCD using the Web interface also doesn't change this.
So it looks like parts work and some don't. I did review all the soldered connections they all look ok, the 1 wire does not have a resistor like in the wiki, this might be the reason that it does not read. I did notice there is a diode depicted behind it, not sure what this is for.
Given the fact that the relay clicks it would look like the HAH works, however the clicking sound is not allways following the web interface, at least it does not always click when toggled. The LCD getting stuck in booting rahter than showing an IP indicates that something is wrong. Currently I have checked everthing and I am not sure what the problem is. The long booting time seems odd, did see in the middle of the board it is slightly discolored and getting pretty warm. I don't know if this is common for Liveboxes. It just an observation. However it appears to be working as expected and comes up with a web interface. Than the other component in the quotation is the ATMega 328. it would appear to work gets powered and seems to trigger relays. The hooked up LCD get information from it and show booting v3.4 could it be getting stuck after this?
I hope anyone with hands on experience can let me know if my observations are normal and hopefully point me in the right direction to get it up and running normally.

Forums

My original HAH PSU seems to have died on me, I'm looking for a replacement and was wondering if anyone had a spare they'd be willing to sell?

I just took delivery of a jeelink usb v3 and jeenode v6 with room plug.

I managed to flash the jeelink with hahcentral.hex and the jeenode with roomnode2.hex

When i run microcom -s 57600 /dev/ttyUSB0 with the jeelink connected it reports:

[HAHCentral.1] D i4 g212 @ 433 MHz 

 

But when i run it with the jeenode attached i don't get anything.
What am I doing wrong?
Thanks!

 

Derek any news as i am ready to order a programmer and want a couple of jeenodes and cable as well.

 

would rather order the whole lot in one go rather than bits n pieces, also jeenode programming cable plugs into usb yes?

 

i suppose it would be bette to do this programming on one of the spare liveboxes i have? i am assuming you just need a hah livebox not expander pcb etc?

 

am i correct.

 

ta dean

Forums

Given my lack of soldering skills I was quite surprised that I actually got my HAH LCD to work. Having said that, after a couple of hours it seems to go blank. Does anybody else have this problem or is it just (as I suspected) my poor quality work. If I switch off the box and restart it, it seems to come back on. Maybe it's a temperature thing as the LCD feels warm to the touch. Any one else have this?

Forums

Hi,

I've recently put together a HAH setup using a complete board from Derek (thanks for shipping this out). I'm nearly all working with the exception of the RF and the external 1-Wire.

Firstly, the header and cable shipped is a 4 way socket, not three as per the notes in the Wiki - Does anyone know if the 4 way header next to the 3 way header is also for 1-Wire? And if so, what is the pinout?

Secondly, I am having problems with the RF setup. I've got the 15v link from the Livebox to the HAH, the RF module is installed but I can't get it to control a Lidl socket. I'm trying the following codes -

rf1.off=0101020D03E803E8020D10011B5818DCB090
rf1.on=0101020D03E803E8020D10011B5818D2C940

I've also tried

rf1.on= 01020320028A05DC028A05DC0514032004B00C029C401515B15556160
rf1.off=01020320028A05DC028A05DC0514032004B00C029C401515B155555540

If anyone could suggest any troubleshooting so I can test the RF?

Many thanks,

Andy