Hardware

Description

Building / testing and troubleshooting the HAH hardware.

Forums

A 433/864 receiver that has the ability to automatically "learn" rf codes fro a TX.

 

How cool would it be!! squirt RF at it and it reprodces it.

 

dreaming i know

Forums

Hi Derek,

Finally, I've got mostly everything up and running. Most initial parts logging to pachube (43437). This whole eco system is great, I'm really looking forward to expanding. Some of the extent of the use from other posts is absolutely amazing. And the roomnode (hint) is going really well.

My stumbling block at the moment is with the basic RF. I've fitted it straigh with the your exteral smb, centre core to the antenna, sheild to gnd. vcc/gnd = 12.15Vish but I just can't get anything to work.

the relays work fine, so I know the comms is good.

I've moved back from the homeasy and started with the lidl plug I bought from you.

To be clear on the lidl plug; switch on at mains, active so the green led comes on; press and hold teach; send 01020320028A05DC028A05DC0514032004B00C029C401515B15556160 via rf1 (tried both flash gui, so I can see xap state change and control tab); release teach button. Press off on gui button and switch doesn't got off etc.

Anything I've missed, any help appreciated.

Cheers,Ian.

I have connected a light sensor to 1 room node and am seeing readings appear on my HAH in the form Node ID followed by an integer similar to 168 and then some zeros.  I have set up my jeenodeApplet.lua file to include light=1 and restarted the serial scheam and plugboard service but I am getting "?" in the value field from the light endnode.

Looking at the source for roomnode2.pde, the payload format specifies that light should come first, followed by moved etc.. My question is should the specification of the endnodes in jeenodeApplet.lua be in the same order as that in the source code of the roomnode?

Thanks for any help


Chris

Forums

I have been experimenting today and simply added a 1/4 wave wire to the ground on the HAHNode to create a 1/2 wave dipole. And, I know its early days, but I am getting a fantastic result.

So, that is an antenna of approx 73mm sticking up from the Antenna hole and a second wire coming out the bottom of the board from the 'G' hole next to the antenna of the same size. 

With this I am getting reliable reports from my allotment Greenhouse (we live next door to the allotments, but my plot is not adjacent). The greenhouse is about 50 metres away but it has to go through 2 double thickness walls and the HAH is stuck down in the electricity cupboard at floor height.

 

Just thought I would share.

 

Derek - FYI, I understand thicker wire make for a wider bandwidth antenna, so if you get the chance to make the holes a little bigger that would be good. Obviously wider bandwidth will help with cutting (in)accuracy for the antenna lengths at such short wavelenghts.

Forums

Hi all,

over the last two nights my outside temp has dropped to and sat at for a period of time, exactly 0.0C. whilst the pachube plots would suggests the temp didnt drop much lower than this I find it a bit too much of a coincidence that the temp fell to exactly 0.0 two nights running.

I am on 298 with 3.4 firmware.

has anyone else reported negative temps on V3.4 of the firmware?

 

cheers,

 

Garry

Forums

Does anyone have a USB hub on their HAH?

Now that I have a HAHNode, I cant use my current cost!

I have tried two unpowered hubs so far, both dont work. Perhaps they need to be powered?

Please post details of any hubs you know that work,

Or is it a config problem? When I look at dmesg, it looks like it only sees one device on the hub.

 

Many thanks

Alan 

Forums

from XFX viwere under jeenode

xap-header
{
v=12
hop=1
uid=FF00D801
class=xAPBSC.info
source=dbzoo.livebox.jeenode:pond.temp
}
input.state
{
state=on
text=-24.6
}

from serial on XFX viewer

xap-header
{
v=12
hop=1
uid=FF00D500
class=Serial.Comms
source=dbzoo.livebox.Serial
}
Serial.Received
{
port=/dev/ttyUSB1
data=OK 2 1 0 10 3
}

so looks like an incorrect UID that i need to change somewhere, anyone any pointers?

Finally got 'round to soldering up the HAHnodes.

Connected up to the Arduino IDE, and data coming though, so looks ok before I connect up to the HAH.

Seems to be lots of data (more than HAH processes) ? Please can you point me to the schema which explains what each value is? Also, seem to be some 'short' records? 

 

[RF12nocfg.1] A i1 g212 @ 868 MHz 

 

Current basenode configuration:

 A i1 g212 @ 868 MHz 

 ? 54 239 45 22 21 232 190 125 192 122 75 173 250 189 82 168 249 62 90 224 188

 ? 12 125 193 0 144 150 130 169 188 131 238 9 208 7 17 11 231 173 233 6 215

 ? 7 14 214 98 57 17 197 68 146 203 16 162 128 113 93 151 107 19 220 168 120

 ? 128 254 97 65 67 62 11 48 1 70 53 113 174 130 155 215 134 131 68 101 22

 ? 61 176 94 217 166 185 245 66 97 161 190 137 4 252 50 7 85 94 133 135 4

 ? 20 248 6 126 18 236 92 79 192 136 127 121 0 31 186 96 154 116 227 110 43

 ? 35 185 162 233 25 40 240 244 195 134 88 127 233 146 17 45 57 54 202 157 198

 ? 25 14 230 24 25 146 91 213 6 245 26 52 115 132 61 1 13 241 195 42 173

 ? 178 83 172 17 248 193 30 227 4 46 8 74 161 223 157 160 212 37 95 83 129

 ? 20 241 151 170 194 45 177 21 90 52 176 155 147 227 192 235 253 145 45 70 152

 ? 225 98 117 211 125 244 120 23 172 180 194 31 118 94 31 136 214

 ? 134 117 152 194 6 135 248 118 247 244 186 130 32 130 117 64 161 1 62 75 116

 ? 62 233 113 155 246 0 254 13 88 245 235 40 83 39 241 20 234 4 3 100 193

 ? 168 241 147 196 138 132 1 22 16 159 7 227 248 6 201 121 157 248 178 69 215

 ? 166 20 238 90 202 253 136 55 130 18 183 122 71 152 58 70 167 88 107 231 224

 ? 54 38 193 209 208 160 130 169 48 124 69 8 145 96 219 73 206 134 234 18 104

 ? 38 185 40 204 130 0 55 167 10 157 255 3 12 142 141 238 121 78 171 225 244

 ? 32 12 136 176 116 81 228 230 121 182 48 240 178 34 100 8 177 172 2 151 199

 ? 150 109 158 235 80 80 38 127 28 6 96 36 84 167 146 211 194 71 140 99 249

 ? 141 124 56 3 50 150 130 150 134 178 136 150 196 5 47 114 161 75 180 127 17

 ? 40 103 248 23 232 2 86 90 246 76 53 116 66 79 174 62 88 41 128 198 201

 ? 30 68 13 254 131 81 195 39 35 235 145 184 30 15 96 44 188 216 10 217 128

 ? 0 39 21 229 0 183 34 4 228 116 144 60 150 118 210 207 24 237 162 50 87

 ? 39 102 167 128 54 117 231 32 147 108 130 175 7 30 230 231 179 89 228 129 15

 ? 174 130 181 172 61 231 95 188 205 82 45 252 136 123 140 54 125 173 167 82 144

 ? 180 39 78 186 183 85 136 132 96 242 135 140 233 165 74 0 155 224 109 159 226

 ? 36 240 12 173

 

Forums

I am a hardware engineer i build things.

what i hate to see (and i am seeing it more and more) is software people being put off by constructing hardware.

"if" i was to construct and test the boards what would be a sutible "charge" for a fully constructed and tested pcb which would just need "plugging in and mounting" to a converted livebox.

I am not saying it would be pretty but it would be functional.

and i hope i am not treading on anyones toes suggesting this?

I don't have a lot of spare time but could make and test a few a month?

comments?

Derek i suspect the only reason you don't offer an assembled and tested kit is the lack of time?

 

Dean

Forums

Hi, 

Firstly, thanks to all the people that have replied to my other posts - its great to see such an active forum. I hope to return the favour when i'm up and running. 

I am .. 

a) still not convinced by the quality of my soldering.

b) still not convinced that the fundamentals of the HAH i've got a working. 

In particular, the reason for my concern is that i got to the part of the instructions where it said "Newer versions of the PCB make provision for an on-board DS18B20" and i noticed that i had soldered the jack for the RF unit in the wrong place. I managed to remove it but in the process don't think the PCB was in one piece. The soldering for the DS18B20 in the place its supposed to be isn't great for sure. 

What is this for? What will i notice not working if its not there?

At the moment i've

- configured twitter, posted a tweet and noticed that it deleted it ( as expected ) but didn't seem to send any xAP messages when i tweeted 'relay 1 on'

- been unable to get the LCD working, despite checking the soldering and cable. 

- seen that it'll find entries in my google calendar but doesn't seem to parse them correctly. 

- running 'lua clock.lua' from /etc/plugboard ( after copying it there ) doesn't seem to send any xAP events to the LCD ( checking via xfx viewer ). 

 

Any ideas?

Thanks ( again! )