Hardware

Description

Building / testing and troubleshooting the HAH hardware.

Forums

Is there anything within the livebox code that would cause a spontaneous reboot? For the past two days I have come home to one of the TVs being on. When I have checked the TV that is on is the one that was last turned on by the HAH. I have the script to log RF states. Yesterday the box still had it's uptime showing 3 days so obviously that was not down to a reboot but today the log shows the TV coming on at 9am ish this morning and the uptime suggests that the box rebooted at that time.

The logs are clear due to the reboot so I can't find the cause from there.

There was also a strange happening last weekend. All the RF recievers turned off at 2pm on Sunday, this time the box did not reboot but nothing strange in the logs.

It's not a major problem, SWMBO is just happy that the heating control is now iPad based :)

Forums

i have a problem.

 

i have 3 jogglers all running xapflash.

sometimes (once every 2-3 days) they stop responding to commands a restart of joggler does not resolve problem.

 

if i go to we pagei can then control rf devices so HAH is sending out commands correctly, even xapflash on webpage does not respond but from admin it works fine.

 

a reboot solves problem or if i wait for 10-20 minutes problem seems to be resolved.

 

i have run xfx viewer and all looks fine BUTno rf on/off is detected whilst problem is exhibited, also if i swith rf on/off several times whilst problem is occuringsaiditem will within 5-10 minutes switch on/off a corresponding number of times.

 

1 how do i debug this

2 anyone else with joggler/xapflash noticed this?

 

driving SWMBO  nuts

 

oh and a rebootof HAH instantly fixes it.

 

Dean

Forums

Hi,

Has anyone experienced the following issue.

Im running HAH Build: 306/3.4

I can switch devices on/off via Twitter but the tweets don't get deleted automatically. The permissions for the HAH app in Twitter seem to be correct with read/write access set.

Pachube feeds are also not working. The heartbeat is being generated but no update messages are being sent.

Google Cal - works like a dream - no problems there.

 

Thanks

Forums

I have been having trouble with HAH board locking up, and after discussion on this forum I have come to the conclusion it is caused by my extensive network of temperature sensors possibly cause a spike on the 1 wire bus.

To resolve this I tried to use a separate 5v power source to power the temperature sensors, but when I connect it up all the sensors show "?". If I unplug the 3.5mm sensor lead and plug my test sensor directly into the port it reads correctly, so I know that the 5V line is wired and working correctly.

Why is it that my multiple temperature sensors only work with the HAH sourced 5v line?

Forums

I'm having a real struggle with my RF which doesn't seem to be working at the moment in spite of working fine throughout last winter, it seemed to give up the ghost sometime during the summer. I've tried a new RF module and a new molex plug on the PCB but I still can't seem to get it working.

With the HAH PCB installed and the box open and powered up I get 12.03 volts between GND and VCC on the RF module and the Module works OK if I plug it into a prototyping board and use an arduino to drive it. I've tried different RF modules and nothing seems to work. I've had occasional success with the box open and flat on the bench but it's not at all reliable. I'ts entirely possible that it's my poor soldering that is at fault but I don't know how to test or what to test to make any difference.

Any suggestions would be gratefully received.

Forums

I have a few LCD displays, some long (64 chars x 2 lines) some short (16 chars x 1 line) and (16 chars x 2 lines).

I thought I may be able to use these with the HAH but putting a 2 line display just causes the text to split over the 2 lines. I've had a look for the LCD bit of code but struggling.....any pointers?

I would like to use a 16x2 display to show a little more information

Forums

I thought I saw a thread some time ago when someone asked if it was possible to connect multiple CurrentCost EnviRs (or other display) to the HAH ?

Has anyone done this/is there support? From memory, there's nothing in their XML that makes them unique, so the USB TTY port number  could be used ?

Forums

Hi all

Just activated another HAHuband I'm getting a wierd problem.... Plugboard won't heartbeat properly!... here's what I'm getting from xFx...

Error Message: Invalid name/value pairing. Address components cannot be empty strings.
Message Line#: 7 - source=dbzoo.livebox..Plugboard
Received From: 192.168.1.20:3079

xap-hbeat
{
v=12
hop=1
uid=FF00D800
class=xap-hbeat.alive
source=dbzoo.livebox..Plugboard
interval=60
port=3645
}

Can anyone point me in the right direction on this, please.  I did have it 'instanced', but I removed the value and its now a vanilla system (confirmed by looking in the xap-livebox.ini file)... I've also forced a reload of 306 and removed any applets from the plugboard dir and it still errors!

Help, please....

regards

EJ

Forums

All,

 

I have reviewed http://www.dbzoo.com/_detail/livebox/pcb_rev1.jpg and this does not match my PCB.

Does anyone have:

a). Updated PCB schematics

b). Can tell me what ver of PCB I have with following data - Only 1 jumper (JP1). below which is my 15v pad, below which is a bolt hole. To left of JP1 is IC1 and above JP1 is jack plug. I have onboard DS18b20 above jack, to left of which is RF connector.

Whilst I am at it, what is best place to pull off 5v - i dont use i2c (yet) so was thinking using the VCC pin, but was hoping there was a more specific vcc tap (also RLYBRD may have a pin I could use - I dont use that set of pads yet either?). Without schematic, i dont want to go poking about too much (I am still at "homo neanderthalensis" stage of evolution in electronics!).

 

--andy

Forums

Just re-flashed the HAH with a beta now if i plug the hah in it "screws" my network.

 

i lose wireless router and the only way to get it working is to reboot the switch that the haha is plugged into and the wireless ap as well

 

the HAH is also not working?

 

anyone else had this problem?

 

(think i am going to be re-building/flashing a HAH)

 

Dean