Firmware

Description

Issues around flashing livebox firmware HAH or Orange ready for jail breaking.

Forums

Help,

Going away imminently, about to "sell" the HAH to HWMBO to turn light etc on and off while away, but the Google Calendar option is missing in version 251.  It's not on the web interface, I looked in the ini file, but no [googlecal] section, so I added it, as per the Wiki, rebooted....  Still not there.

Has anyone else noticed this?

Derek/Brett, if you can squeeze it into 252 I'll be happy to beta test, or have I just made a stupid mistake and not looked hard enough, I'll go and read through again just in-case.

Thanks

 

Karl

 

Update 1:

The xap-googlecal service won't start if the google credentials are wrong, corrected this.

But, I still can't see the page on the web interface, no big problem.

 

Update 2:

Just checked the source code, and although you can call kloned with calendar.kl1 and see the settings, something is wrong with it.  (note to self: Try harder to get dev. environment up and running)

 

Update 3:

The menu.kl1 doesn't seem to have a section for the Google calendar.  I think it needs a line like {"Automation","Calendar","calendar.kl1", NULL} inserting between lines 28 and 29.  Update 2 still stands, the Calendar configurations does display, but not correctly, if called directly from the web browser address bar.

Forums

Hi Derek,

As you know I'm busy building my xAP remote control system for my Joggler.

I have now finally connected a CC monitor to my HAH, no problem.

When trying to get the level details to display on my Joggler I have come accross some issue with what is expected in the xAP message.  I don't fully understand all this but as far as I can tell and have been reliably informed, our xAP messages from the CC monitor aren't well formed.

Aparently the xAP spec says levels should be formatted so: level=value/max  eg level=944/10000

This allows for percentile calculations to made based on the value.

I've also noticed another issue, which has been highlighted in my endeavours.  Sometimes my controller seems to loose any idea of what status the hah thinks the rf devices are in.  Now I know that the devices don't actually respond but I would assume that correct or not, the HAH would also have an 'opinion' as to what the status should be.  It seems that it doesn't always want to reply to requests for this opinion and so the status of my controller disappears.

I hope I've explained these well enough, I would be happy to do some more diagnostics, you'll just need to let me know what to do?

Thoughts?

Gary

Forums

My upgrade went without a hitch.

I can confirm the RF modules > 4 do seem to work although this did work for me on 250 after ini config?

 

I do have 1 problem with the 5th home easy RF module that I've added.

When I throw it into my system, it works fine for about 10 secs, then turns itself off.

It then seems to disrupt all the other devices, i.e. It's label is rf5, if I turn it on, RF1 will turn on as well.  This is one example and other stuff will happen too.

 

I'm putting this one down to a rogue device and will change it for a new lot unless you wanted to see what this device was doing, would be happy to send it over.  Not sure as you'll have time what with all the other stuff you guys got going on...

Forums

Hi

 

I bought a livebox on ebay and it seems to work ok (I can login to the box using the browser in normal mode)

 

However, the repair utility times out every time. I have tried disabling the firewall and antivirus and disconecting the primary ethernet port from my main router, but with no success.

 

I get the three leds ok, and then the repair utility counts down, By the time it reaches zero, the leds have gone to a single flashing one and sometimes several leds flashing.

 

I am using win7 not sure if this has any bearing. Not much else availabe with windows here

 

Many thanks for any clues

 

Alan

Forums

Hi, I'm trying to get access to the eeprom dump of microcontroller using this command:

microcom -s 115200 /dev/ttyS0

When I enter this, my system becomes unresponsive to keyboard and starts displaying all the 1wire outputs.
I can't even CTRL C, but have to close the session.

My plan was to add a few more RF sockets.
Any suggestions
Cheers
Gary
Forums

How excited was I.  Found your site via Automated Home, hunted down a Livebox, and then bricked it.  I was so excited, it's the first time I've tried something like this, but I missed one key part, I didn't unzip the reboot_blueg5.6-patched.gz file, and just copied that into /dev/mtd0.  I hope this is a warning to everyone else not to rush. 

Will I try again?? JTAG looks way beyond me, and I can't really see me buying another box, so it looks like a trip to the recycling, oh well.  Pretty fed up really, reader be warned.  The instructions are good, make sure you read them!

Keep up the good work guys, I'll keep looking back to see how HAH develops.

Forums

Hi. I flash Livebox of Orange(spain)

 

I used for Telefonica ADSL and works, sincronice, etc....but when i opened a webpage, appears a page saying "there is a new firmware, please dont turn off the livebox"...then, the livebox start to actually to a new firmwareand blocked again for alone being used for orange...

 

 

Please, help ¡¡¡¡