Firmware

Description

Issues around flashing livebox firmware HAH or Orange ready for jail breaking.

Forums

I am having problems getting HAH running on my Livebox.  I looked at the telnet approach to console access and decided this was definitely beyond my capabilities. Hence have now purchased a dbZoo console cable.

I have now got access to the Livebox having installed v5_04_3-uk and changed the password as described. So now I am trying to use the serial port for console access.

Managed to find an old laptop with XP and a serial port and have changed its Com1  port setting to those in the dbZoo  write-up, and also installed putty and xfx viewer.

Have now opened putty and clicked serial connection, but when I click OPEN,  nothing happens.

Tried to see if there was anything useful on xfx viewer and this just shows the laptop connected.

Have been through the same process a number of times and now am totally frustrated as I know it is almost certainly my lack of understanding which is the problem.

 

Any help would be most welcome

Forums

When trying to build the latest source on Ubuntu 13.04, I've found a couple of issues :-

The xap-flash Makefile has a line :- 

install -m 444 *.{swf,png,jpg,xml} $(INSTALL_DIR)/usr/share/flash

This throws an error :-

install: cannot stat '*.{swf,png,jpg,xml}

A workaround is to include 4 seperate lines for each file type :-

install -m 444 *.swf $(INSTALL_DIR)/usr/share/flash
install -m 444 *.png $(INSTALL_DIR)/usr/share/flash
install -m 444 *.jpg $(INSTALL_DIR)/usr/share/flash
install -m 444 *.xml $(INSTALL_DIR)/usr/share/flash

NOTE: The next time you sync with the repository you will get a conflict.

The second problem is that there is no root user as such, so at the end of the build process when you get prompted for the root password, whatever you enter is wrong.  To overcome this it is necessary to run the make command like this and enter your password when prompted, a downside of this is that root then owns all the files :- 
$ cd livebox-hah-read-only
$ sudo make
A workaround for this would to to change the lines below in the HAH Makefile, but again, you will get a repository conflict the next time you sync.
Under the buildimage section:
su --command="cd $(TARGETS_DIR); ./buildFS"
to
sudo su --command="cd $(TARGETS_DIR); ./buildFS"
Under target_clean section:
su --command "rm -fr $(TARGET_RS)"
to
sudo su --command "rm -fr $(TARGET_RS)"
There may be better solutions, but these worked for me.
Forums

Ok, after following the HAH for a while now i decided to take the plunge and got a box off ebay. it arrived and great i thought. today went through the process to install HA but seem to have hit a "brick" wall. 

this is what i did.....

Downgraded firmware from 5.10.7-uk to 5.04-uk. this was successful (using the 'RGWRepair.exe' software)

Then i did the windows telnet/ftp method, and could successfully open a telnet session to the livebox

I then got a little carried away and did step 7. Stopping 'phone home' behaviour.

Next i then moved onto the Replacing the RedBoot loader. i downloaded redboot_blueg5.6-patched.gz and extracted this on my windows machine.

then from a telnet session ran:

# cd /tmp
# wget ftp://<HOST SERVER>/redboot_blueg5.6-patched (pointing to my ftp server)

# fcp -v redboot_blueg5.6-patched /dev/mtd0

this last command did some small write..... i forget the rest. no mention of any error. i was slightly relieved at this point as the warning of bricking your device if you did extract the file.

I then downloaded firmware-287.zip and ran the RGWRepair.exe program to use this and at the point of putting the power cable back in the hub and holding down 1, this is when things have gone wrong.

all I am left with is a single red light in the middle. (i believe the >> led)

is the device bricked? did I miss something or could this be something else the matter? do i now need to JTAG this? 

hope someone can help me with some ideas/solutions.

Regards,

Michael

Forums

I've gone and bought another 'livebox' so I can carry out my new years resolution. I flashed my livebox into a fully functioning HAH using my mac last year. I based my work on the wiki but I did promise to create a write up on how to do this on a mac. You guessed it, I never got around to it and so I am going to do it all again but this time I will have pics, screenshots, step-by-step etc etc

Here's hoping it will help someone in the future

Forums

 

I have tried the 307.1 beta and while the 20x4 lcd works wonders for me, I am having problems with the temperatures and light levels feeding backfrom the roomnodes.

roomnode[2] is working ok for temperature, thanks goodness as that one controls the central heating but the light level feedback is erratic.

roomnode[3] is showing my conservatory at 20C + and I know it's not that warm ;)

roomnode[4] is my gas monitor and I am using the humi to store the pulses from the meter and previously I was getting 11 pulses max per transmit cycle, now I get 64 :) oh and it's 23C outside, time to sunbathe :)

I know there is the toff and toff2 offset I can now add but excuse me for being stupid but where do I add it?

rolling back to 307 as that works fine (thanks Brett)

I have tried looking for differences between 307 and 307.1 but I can see nothing that would cause this

Forums

Brett

I have updated to 307 with no issues, however, I wanted to use pl.xml to parse an xml file as you do in your weather applet(thanks for these examples by the way they really do show how to use the scripting language better than any manual).

I believe to use this I need to update to the 307.1 beta for the penlight uplift, however, I have tried to update to this beta three times now and whilst the update appears to go ok, after reboot the HAH is dead. 

I can easily reflash back to 307 and all is OK.

Not sure if there is a problem or just my system but thought it worth a heads up

Ill have to leave well alone for now as I can't risk loosing the heating for too much longer before I get the SWMBO giving me grief!

thanks,

 

garry

Forums

Hi All,

just got my Livebox up and running HAH and spent this evening setting up the excellent iServer & xAPFlash on one of my Jogglers

next step order the HAH parts bundle from the shop and see if i can get it all talking nicely to my Home Easy range in time for my xmas light demo to the SWMBO!!

i noticed the latest firmware on http://code.google.com/p/livebox-hah/downloads/list is rev 287 dated oct 2011 - flashed to my box

i also noticed some of the screenshots on the xAP wiki show the version 299 with the GUI tab and xAP flash layout built in

is it possible to obtain a copy to test or was it withdrawn?

Thanks Andrew

Forums

Hi everybody,

This is my first post.

I've already flashed my livebox with openwrt (Backfire 10.03.1) and would like to flash hah-firmware on it.

Seems redboot only tries to load openwrt-livebox.bin, factory_script or /inventel/blue_5g/factory_script but no /inventel/blue_5g/factory_script_crypt ... so tell me if I'm true guessing that the files that should be served by tftp are uncrypted.

Should I decrypt the hah-firmware.dwb ? If yes, how can I achieve this ? Don't know how to ...

 

Thanx in advance for your interrest

 

Ronald

 

Forums

Trying to get HAH up and runnoing on my Livebox. Using the instructions on DBZoo

I've managed to downgrade my livebox to v5.03.3-uk

Next it says I need to get command line access

I can access the livebox through the brower and have changed the network settings to

10.0.0.1 etc

PC is set to 10.0.0.2 etc

Downloaded the etc.tar file on step 4

after that it has some command line code. What do I do with that?

I can't connect to the livebox with filezilla server or command prompt - Telnet

It mentions changing the Livebox name then shows more code.

Thanks in advance