Hardware

Description

Building / testing and troubleshooting the HAH hardware.

Forums

I have a few cables "spare"

 

I am selling on ebay at £7.99 For HAH users i will give a £1 discount just let me know in the messages field you are a HAH member and send payment for full amount and i will refund £1.

 

I do refund as i had one sale where they said "my brother said if i mention i am a hah user you will discount p&p" cheeky begger but i did as i am honest like that!!

 

thats Just £6.99 for a proper brand new currentcost cable inc P&P


Its a deal its a steal it's sale of the f*****ing century (to quote one of my fav film line's, lock stock and 2 smoking barrels)

Forums

Hi,

I have a Wanadoo Livebox which is actually a Sagem F@ast 3202.

Is this hardware suitable for the HAH project?

I've tried to get into programming mode but it seems to be different for this livebox (there are no "1" or "2" switches, but "RST" and "REG" ->tried either one while powering up; so far no luck)

The HMI via 192.168.1.1 is working and shows s/w version 3202_2601D8.

Thanks,

John.

Forums

Hi All,

I was wondering if someone could confirm if the behaviour I'm seeing on my inputs is normal or due to my less than adequate soldering.

I have connected my house alarm bell output to a 12v relay and wired this via cat5 cabling to an input on the HAH. A script then sends a twitter message (and hence a pop up on my mobile) when the house alarm is triggered. This all works but I am getting the odd false alarm.

I immediately blamed my wiring and have since checked and double checked connection integrity.

On further investigation though, I noticed that by touching just one of the screw down terminals with a paper clip would generate a very brief on/off message (viewed in xfx, lasts millisecs) even though I didnt short the two terminals. I just need to touch one screw. This happens on all four inputs. I assume the some change in resistance/capacitance (?? my electronics is not good) of the terminal is triggering the input briefly.

I therefore assume that the resistance/capacitance of the wiring is changing slightly due to RF interference etc and creating a brief on/off signal from time to time and hence triggering a false alarm.

I can script round this with timers etc so only trigger an event after after a few secs of input being on but was wondering if this behaviour is normal or if I have a problem.

 

Thanks for any info as always,

 

Garry .

Forums

Hi great project. sorry if this is a nieve question.

I want to buy the parts bundle to give my HAH relay and input capability but want to also keep the Rf options open for future use.

I am on 279,13 firmware therefore I believe I need an AVR328 chip. Can i simply put this chip on the board instead of that supplied with the kit? do i need to do anything else (i noticed  a avr328.hex type file for download but cant figure out what this is for). like i say, sorry if this is obvious but want to be sure i know what the score is before purchasing.

 

many thanks again for the time you put into this. I am having a great time playing with it.

Garry

Forums

Just an update to say I have managed to set the resolution on my network of DS18B20 sensors using a DS9490 USB adaptor and the one wire viewer from Maxim.

The DS18B20 has 9,10,11,and 12 bit resolution, set using bits 5 & 6 in the onboard Configuration Register - the power up default is 12 bit, but can be re set in the free windows appz from Maxim.

My network now seem to retain these setings when its re connected to the HAH.

Regards

 

Harry

Forums

Hello All

Just a thought, would anyone be interested in collaborating on a HAH shield, compatable with the existing arduino.cc spec, and supporting an enhanced 1wire RJ45 line driver, with 433 Mhz TX and possible 433 Mhz RX?

Regards

Harry

Forums

Having put the pcb board and display inside the box - I temporarily left the temperature sensor inside (in a plastic bag to avoid possible shorts!).

The graph below shows the temperature changes - it seems to go up and down once an hour.  So presumably the hardware is

working harder and then resting (cooling).  Any ideas? - just curious.  Note the sensor works fine - and I have moved the box around to prove that it is not location.  The general rise and fall aligns with house temperature as shown on nearby currentcost meter.

My feed is at http://www.pachube.com/feeds/13194 if you wish to see the days prior to the changeover.