Sanity check the livebox / HAH

Hello all!

So, i've just finished building my livebox. I'm not normally one that is often seen with a soldering iron and so i'm quite pleased that i've been able to get it all on the board neatly. Unfortunately i also don't have a multimeter and so powering it up involved a lot of crossed fingers. Never the less, after a few issues getting it on the right network i'm now able to see an IP address on my router and i get to the web interface. 

Member for

15 years 1 month

allanayr

14 years 11 months ago

login is root, password is admin. That should get you in. On the web interface page if it says "Build 301/3.4" or similar, you would be seeing that the HAH pcb is being detected. Try downloading the virtual LCD from the site it should at least show you what should be visible on the actual LCD.

Hope this helps a bit.

Member for

14 years 11 months

af199

14 years 11 months ago

:) Thank you for the quick reply. root / admin was about the only combination that i didn't try! I can see 'Build 298/3.4' so i'm guessing that all my dodgy soldering has actually got something to work at least! :) 

I've downloaded what i think is the virtual LCD application you mention but it seems to be showing the same thing as the physical LCD shows - specifically nothing! :( I've even tried giving it messages from the Automation -> Control pages but i get no change. At this point i should add that technically i'm on a different network to the livebox at the moment - its on a 192.168.1.x network and i'm on a 192.168.2.x network. Will that matter? I can still access the web interface and SSH in etc. I guess its good to see that the two are showing the same, but any reason why it would be showing nothing?

Thanks, Andy. 

Member for

15 years 1 month

allanayr

14 years 11 months ago

I'm not really a networking expert but my gut reaction is that you should check that you are on the same sub-net (255.255.255.0) or whatever. If that doesn't help then perhaps networking is the issue but others may be able to be more help.

Member for

17 years

derek

14 years 11 months ago

Install xFx viewer on a PC that is on the same subnet as the HAH. You will then be able to see the xAP messages from the HAH. On the LCD front, do try adjusting the little trimpot. 

It would also help if you can post up a screenshot of the UI ... then we can see if the inputs on you HAH PCB are being read correctly.

Cheers,
Derek.

Member for

17 years

derek

14 years 11 months ago

Install xFx viewer on a PC that is on the same subnet as the HAH. You will then be able to see the xAP messages from the HAH. On the LCD front, do try adjusting the little trimpot. 

It would also help if you can post up a screenshot of the UI ... then we can see if the inputs on you HAH PCB are being read correctly.

Cheers,
Derek.

Member for

14 years 11 months

af199

14 years 11 months ago

Hi, 

So, i've been able to get my laptop on the same network and installed the viewer to see the xfX events. I can rather satisfyingly see 4 inputs, 4 relays ( what are these? ) and 4 RF channels. They all seem to be off at the moment. I've also decided to plug in my current cost meter ( CC128 ) and also get a currentcost:ch.1 event as well. These show the current watt reading from the display. At least i know this part of it is working! 

I'll happily send screenshots, but which screen do you need?

Given that the CC128 was working, i also tried a Pachube feed. I have the following settings ( see attached ) but the feed appears to be frozen. 

My only other 'want' is to get / test the RF system. Is there any way of sanity checking this is working?

Thanks to all that have helped so quickly so far. 

Andy. 

Attachments
hah.jpg (40.37 KB)