How was it for you?

Description

A place where folks who have tried the HAH can leave feedback on their experience

Oh waht joy.

 

all i can say is don't try it on a 64 bit windows 7 pc/lappy.

 

had to dig out my old XP laptop (that i use to interface to cars) to flash router.

then forgot to switch off firewall so no ftp in (stumped me for another 20minutes)

then useless livebox wouldnt power up (child had switched off extn lead coz daddy was not being fun "she's 6!!!!")

hour later of lots of fun she agreed daddy could "play" again and she would leave him alone and do painting.

havin lots of fun.

 

regards

 

Dean

 

AKA G7PKF

I finally got the correct cable for my Nokia 6210.  Only the DLR-3P worked for me.

I was still having trouble getting messages from my phone although it was connecting properly.  Looking in XFX, I was only getting heartbeats.  I put it into debug mode to test.

It would see the messages coming in but was throwing up an error. 

(Sorry didn't take a copy of the errors) but the messages included: Failed to collect msg 97, sms error 321.

I found this listing of errors: http://www.dreamfabric.com/sms/cms_error.html

My error was something to do with memory, so I tried deleting all the messages in the Inbox, this didn't work, all the messages were still there(tried this a couple of times), so I had to individually delete each message.  After restarting xap-sms, I got my first message in!

During all this, the system was crashing.  It seemed to be after restarting the system and then killing the xap-sms process in order to restart it in debug mode.  If I then ctrl-c, then started the xap-sms process again, it would kick me out of my ssh session and the web would become unresponsive.  The only way to sort it was to restart the system by hand.

I've tried this again and it seems to still be an issue even though my phone is now functional.

I guess the only thing that may cause the problem is restarting xap-sms too quickly?  I was restarting after 4 or 5 secs, maybe phone was still closing the session.

 

Just so you can see what a good message looks like on debug level 7 (command: xap-sms -d 7):

Using serial device /dev/ttyUSB0

Serial Tx: AT+CREG?
Serial Rx:
+CREG: 0,1

OK

Modem is registered to the network
Serial Tx: AT&FE0+CMGF=1;+CNMI=2,1,0,0,0
Serial Rx:
OK

Serial Rx:
Serial Rx: +CMTI: "MT",1
trying to get stored message 1
Serial Tx: AT+CMGR=1
Serial Rx:
+CMGR: "REC UNREAD","+44********",,"10/07/28,11:08:22+04"
Testing

OK

decoding: "REC UNREAD","+44********",,"10/07/28,11:08:22+04"
Testing
Saved to /tmp/pdu.txt
Serial Tx: at+cmgd=1
Serial Rx:
OK

Having a bit of bother getting the Current Cost Envi 128 working.  It's receiving information from the wireless transmitter, I can see data on the display.  I've connected the display to the Livebox, using a Current Cost RJ45-USB cable.  I then had to get a USB A Female to B Male, http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItemVersion&item=25049762689…, to connect the Current Cost to the Livebox.  I'm using build 250.

The problem I'm having is that the Livebox can't seem to connect to the Current Cost.  If I run the xap-currentcost script manually I get the following output :-

# ./xap-currentcost

Current Cost Connector for xAP v12
Copyright (C) DBzoo, 2009

br0: address 192.168.1.5
br0: netmask 255.255.255.0
Autoconfig: xAP broadcasts on 192.168.1.255:3639
xAP uid=FF00DC00, source=dbzoo.livebox.CurrentCost
Broadcast socket port 3639 in use
Assuming a hub is active
Socket port 3639 in use
Socket port 3640 in use
Socket port 3641 in use
Discovered port 3642

Using serial device /dev/ttyUSB0

Unable to open the serial port /dev/ttyUSB0

I've tried other USB port numbers, but I get the same problem, I've also tried rebooting the Livebox.  I can only think that I haven't connected the Current Cost to the Livebox correctly, but I can't see another accessable USB port on the Livebox. 

Any ideas? 

I'm keen to get this going so that I can move onto your add-on unit and start turning things off remotely.  On that subject, I noticed Asda selling a pack of 3 RF plug sockets for £5.  Any chance of getting those going, I'd be happy to test, but I think I'll need more that 3.

Thanks for any help,

Karl

PS - I like the new notification feature, keep up the good work.

OK, so I have my AVR board built, my LiveBox reflashed with the HAH firmware and my AVR connected.

When I start the system, I get "Booting..." on my LCD, then I get "Acquiring IP", then I get nothing.

I don't seem to be able to access any of the IPs used along the way  or the default IP for the LiveBox.

The lights I get are (1st left flashig, middle perm nothing else).

I get no entry in my dhcp server for a new device.

 

The only clue I have is that when I had the board disconnected and turned the device on, I got an entry for a "BAD_DEVICE".  The MAC address seemed to be very short(6 or 8 chars).  I seem unale to repeat this now.  I have re-checked all my soldering etc.

 

Any ideas?

Hi guys, thanks for the very quick delivery of kit.  I picked up a livebox for £1.04 + postage last week and just waiting for it's arrival.  I'd just like to give you some feedback on my expereince of building the microprocessor board.

The instructions in general were great.  I think the only area where I got a little unsure of what was required was when installing the RF module.  I'm not sure about the height at which it now sits.  Maybe a closeup picture might help.

Other thing maybe worth mentioning is that my board came partly populated.  If this is now a standard, I would update the flow of the instructions to provide a quick check on what's been installed and then what to follow on with.  I imagine however that I was lucky enough to get a board you may have already started on?

I did however run in to one rather unfortunate problem.  When it came to soldering on all the connector blocks, with my confidence running hi, I just whacked them all on and then quickly ran out of space at the end.  I just couldn't get the last one to site in.  I then noticed the little ridges on the side of each block that allow for locking them together.  This however means the connector blocks need to be fitted from one direction(I did them from the wrong direction). 

My problem came when trying to unsolder them all.  One of the solder pads came off(couldn't solder sucker enough solder off).  This has resulted in one pin on a block has no connection to the relay.  I will need manually connect the correct pin of the relay to the pin of the connector block.

The connector block in question is the one directly under the xtal device and the pin is the 2nd from the left(with the connector block at the bottom as you look at it, 6th from left if you take other block into account).  I think it should connect to the 2nd pin down on the left of that relay.  This is where the others seem to connect to but when I hold it up to the light I can't see a track that goes there...can you help?

As more people tryout the Livebox reflashing and HAH firmware, it has been suggested that a forum where folks can note their experiences would be a good idea. So, feel free to list both 'gone well' and 'not gone well' items.