When things 'just work' you kinda forget how it was put together all that time ago.
I'm guessing that the Busybox on the HAH is struggling to understand your new USB device. You probably reckoned this yourself from the logfile messages.
Perhaps try an 'older' USB to serial adapter. Until you see the USB device being accepted cleanly, it's probably not going to work for you.
I seem to recall that different USB hubs may present the interfaces as /dev/ttyACM0 or something odd like that, you may find that is what is happening which is why /dev/ttyUSB1 not longer exists. Do I define ttyACM0 device? I don't recall. A quick search on the forums tells me that I do.
Is the "lsusb" command available in the busybox? What's its output.
I recall trying a few powered USB hubs with my HAH. More by way of testing to check that the built-in drivers would support a couple of different hubs.
Will go have a dig in my basement to see if I can find one (I rarely throw anything out). If I find one that works with my HAH, I'll send it on.
Hello again, I've just purchased a new Belkin powered USB hub connected everything up however still getting a similar log/error message in /var/log/xap-currentcost.log
[crt][currentcost.c:580:setupSerialPort] errno 19 (No such device)
[crt][currentcost.c:580:setupSerialPort] Failed to open serial port /dev/ttyUSB1
DoubleSpeed just a line to say that I tried a number of USB hubs before I found one that worked, I am currently using an un-powered one, which was a gift from an airline I flew with many years ago. All I can say is try one of the cheap ones you can find on ebay.
One thing to take into consideration if you are using a un- powered USB HUB is the HAH available power. I only have 2 connections.
I'm afraid I'm not going to be too helpful either, just to say your messages output looks pretty much identical to mine up to
hub.c: USB new device connect on bus1/1, assigned device number 2
which is presumably the point at which it encounters the new hub. Mine then does this and ends.
usbserial.c: PL-2303 converter detected usbserial.c: PL-2303 converter now attached to ttyUSB0 (or usb/tts/0 for devfs) Algorithmics/MIPS FPU Emulator v1.5
If I plug in a 4 port unpowered hub it says this:
Freeing unused kernel memory: 60k freed hub.c: USB new device connect on bus1/1, assigned device number 2 hub.c: USB hub found hub.c: 4 ports detected Algorithmics/MIPS FPU Emulator v1.5
Member for
17 yearsA possible USB driver issue
Hi DoubleSpeed,
Yes, it has been a while ... like years.
When things 'just work' you kinda forget how it was put together all that time ago.
I'm guessing that the Busybox on the HAH is struggling to understand your new USB device. You probably reckoned this yourself from the logfile messages.
Perhaps try an 'older' USB to serial adapter. Until you see the USB device being accepted cleanly, it's probably not going to work for you.
All the best.
Derek.
Member for
14 years 7 monthsThanks for coming back to
Thanks for coming back to me Derek, I'm confused as to what is going on as I'm getting conflicting messages e.g.
Seems to like the USB HUB:
Freeing unused kernel memory: 60k freed
hub.c: USB new device connect on bus1/1, assigned device number 2
hub.c: USB hub found
hub.c: 4 ports detected
hub.c: USB new device connect on bus1/1/1, assigned device number 3
hub.c: USB hub found
hub.c: 4 ports detected
Algorithmics/MIPS FPU Emulator v1.5
However...
xap-currentcost.log now says:
Current Cost Connector for xAP v12
Copyright (C) DBzoo, 2009-2012
[crt][currentcost.c:580:setupSerialPort] errno 19 (No such device)
[crt][currentcost.c:580:setupSerialPort] Failed to open serial port /dev/ttyUSB1
Member for
14 years 7 monthsAlso if I remove the USB Hub
Also if I remove the USB Hub and connect the CC as the only USB device the logs say:
hub.c: USB new device connect on bus1/1, assigned device number 3
usb.c: USB device not accepting new address=3 (error=-145)
Member for
16 years 10 monthsI seem to recall that
I seem to recall that different USB hubs may present the interfaces as /dev/ttyACM0 or something odd like that, you may find that is what is happening which is why /dev/ttyUSB1 not longer exists. Do I define ttyACM0 device? I don't recall.
A quick search on the forums tells me that I do.
Is the "lsusb" command available in the busybox? What's its output.
Brett
Member for
14 years 7 monthsThank you, Brett, I will give
Thank you, Brett, I will give this a try and report back!
Member for
14 years 7 monthsSorry for the delay in trying
Sorry for the delay in trying this, only seem to have time on the weekends at the moment..
I've tried /dev/ttyACM0 (also /dev/ttyACM1 in case that might have worked) getting this in the logs:
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Ebtables v2.0 registered<6>NET4: Ethernet Bridge 008 for NET4.0
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 60k freed
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: USB device not accepting new address=2 (error=-145)
Algorithmics/MIPS FPU Emulator v1.5
hub.c: USB new device connect on bus1/1, assigned device number 3
usb.c: USB device not accepting new address=3 (error=-145)
[crt][currentcost.c:580:setupSerialPort] errno 22 (Invalid argument)
[crt][currentcost.c:580:setupSerialPort] Failed to open serial port /dev/ttyACM0
Member for
14 years 7 monthsHi All,Can anyone help me
Hi All,
Can anyone help me with the above?
Member for
17 yearsOlder kit
I recall trying a few powered USB hubs with my HAH. More by way of testing to check that the built-in drivers would support a couple of different hubs.
Will go have a dig in my basement to see if I can find one (I rarely throw anything out). If I find one that works with my HAH, I'll send it on.
Derek.
Member for
14 years 7 monthsThank you, Derek, I'd very
Thank you, Derek, I'd very much appreciate that!
Member for
14 years 7 monthsHello again, I've just
Hello again, I've just purchased a new Belkin powered USB hub connected everything up however still getting a similar log/error message in /var/log/xap-currentcost.log
[crt][currentcost.c:580:setupSerialPort] errno 19 (No such device)
[crt][currentcost.c:580:setupSerialPort] Failed to open serial port /dev/ttyUSB1
/var/log/messages says:
arcs_cmdline: boot_loader=RedBoot root=1F01 mem=16M
Boot loader : REDBOOT
prom init
CPU revision is: 00029107
Primary instruction cache 16kb, linesize 16 bytes (2 ways)
Primary data cache 8kb, linesize 16 bytes (2 ways)
Linux version 2.4.17 (brett@v02) (gcc version 3.2.2) #2 Wed May 15 10:42:50 GMT 2013
Determined physical RAM map:
memory: 00fc0000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 00fc0000 @ 00000000 (usable)
On node 0 totalpages: 4032
zone(0): 4032 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: boot_loader=RedBoot root=1F01 mem=16M
bcm_console_setup
Calibrating delay loop... 254.77 BogoMIPS
Memory: 13896k/16128k available (1462k kernel code, 2232k reserved, 100k data, 60k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
mpi: No Card is in the PCMCIA slot
PCI: Fixing up bus 0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
pty: 256 Unix98 ptys configured
brcmboard: brcm_board_init entry
New led 8, mask : 0x00000001
New led 0, mask : 0x00000002
New led 9, mask : 0x00000004
New led 6, mask : 0x00000008
New led 1, mask : 0x00000010
Module bcm63xx_cons.c v1.0
date: Mar 16 2013 time: 03:52:03 - FPERIPH:50000000
block: 64 slots per queue, batch=16
SCSI subsystem driver Revision: 1.00
request_module[scsi_hostadapter]: Root fs not mounted
DBW flash: probing 16-bit flash bus
Physically mapped flash: Probing for AMD compatible flash...
mfr_id 0x00000001, dev_id 0x0000227E, dev_id2 0x00002210, dev_id3 0x00002200
Found AMD AM29BDS643D
table[i] : mfr_id 0x00000001, dev_id 0x0000227E, dev_id2 0x00002202, dev_id3 0x00002200, long_dev_id 1
Found AMD AM29LV640MB
table[i] : mfr_id 0x00000001, dev_id 0x0000227E, dev_id2 0x00002210, dev_id3 0x00002200, long_dev_id 1
Found AMD AM29LV640MB
Physically mapped flash: Found 1 x 8MiB AMD AM29LV640MB at 0x0
mtd_info :
type 3, size 0x00800000, erasesize 0x00010000, name Physically mapped flash, index 0, numeraseregions 3
mtd_info->priv : amd_flash_private : device_type 2, interleave 1, numchips 1, chipshift 23<5> mymtd is : 80f67220
Support for extended flash memory size : 0x00800000 ; ONLY 64MBIT SUPPORT
RedBoot partition for 64MBit non aligned Flash
RedBoot partition for 64MBit non aligned Flash
RedBoot partition for 64MBit non aligned Flash
RedBoot partition for 64MBit non aligned Flash
RedBoot partition for 64MBit non aligned Flash
Using RedBoot partition definition
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00030000 : "RedBoot"
0x00030000-0x00750000 : "user_fs"
0x00750000-0x007f0000 : "jffs_system"
0x007f0000-0x007ff000 : "FIS directory"
0x007ff000-0x00800000 : "RedBoot config"
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Enabling device 00:09.0 (0000 -> 0002)
usb-ohci.c: USB OHCI at membase 0xc007db00, IRQ 20
usb-ohci.c: usb-00:09.0, PCI device 14e4:6300
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver acm
acm.c: v0.21:USB Abstract Control Model driver for USB modems and ISDN adapters
usb.c: registered new driver serial
usbserial.c: USB Serial support registered for Generic
usbserial.c: USB Serial Driver core v1.4
usbserial.c: USB Serial support registered for FTDI SIO
usbserial.c: USB Serial support registered for FTDI 8U232AM
ftdi_sio.c: v1.2.0:USB FTDI RS232 Converters Driver
usbserial.c: USB Serial support registered for PL-2303
pl2303.c: Prolific PL2303 USB to serial adaptor driver v0.91
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 1024)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Ebtables v2.0 registered<6>NET4: Ethernet Bridge 008 for NET4.0
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 60k freed
hub.c: USB new device connect on bus1/1, assigned device number 2
hub.c: USB hub found
hub.c: 4 ports detected
Algorithmics/MIPS FPU Emulator v1.5
hub.c: USB new device connect on bus1/1/1, assigned device number 3
usb.c: USB device not accepting new address=3 (error=-145)
hub.c: USB new device connect on bus1/1/1, assigned device number 4
usb.c: USB device not accepting new address=4 (error=-145)
hub.c: USB new device connect on bus1/1/2, assigned device number 5
usb.c: USB device not accepting new address=5 (error=-145)
hub.c: USB new device connect on bus1/1/2, assigned device number 6
usb.c: USB device not accepting new address=6 (error=-145)
hub.c: USB new device connect on bus1/1/4, assigned device number 7
Any idea what is wrong?
Member for
13 years 4 monthsI tried a lot of different USB hubs
DoubleSpeed just a line to say that I tried a number of USB hubs before I found one that worked, I am currently using an un-powered one, which was a gift from an airline I flew with many years ago. All I can say is try one of the cheap ones you can find on ebay.
One thing to take into consideration if you are using a un- powered USB HUB is the HAH available power. I only have 2 connections.
Best of luck.
kema..
Member for
14 years 7 monthsJust to ask again if anyone
Just to ask again if anyone can help me with this issue?
Member for
15 years 1 monthI'm afraid I'm not going to
I'm afraid I'm not going to be too helpful either, just to say your messages output looks pretty much identical to mine up to
hub.c: USB new device connect on bus1/1, assigned device number 2
which is presumably the point at which it encounters the new hub. Mine then does this and ends.
usbserial.c: PL-2303 converter detected
usbserial.c: PL-2303 converter now attached to ttyUSB0 (or usb/tts/0 for devfs)
Algorithmics/MIPS FPU Emulator v1.5
If I plug in a 4 port unpowered hub it says this:
Freeing unused kernel memory: 60k freed
hub.c: USB new device connect on bus1/1, assigned device number 2
hub.c: USB hub found
hub.c: 4 ports detected
Algorithmics/MIPS FPU Emulator v1.5
Sorry I can't be any more help.