Problems with SMS

OK, I'm not getting any connection to /dev/ttyUSB0...but I'm certain it's not HAH.

I ordered some RS232 to USB cables and an RS232 data cable for my nokia 6100.

The first problem I have is that the data cable that has been sent isn't what I ordered, it basically replaces the battery and the sim.  Seems to be for unlocking the phone but definitely doesn't work with HAH, or Nokia Data suite for that matter.

If anyone ineeds a data cable for a Nokia 61**, you're looking for a dual bus(F-Bus/M-Bus auto switching), RS232 cable.  This allows you to send sms.

Member for

16 years 10 months

brett

16 years 4 months ago

You need to identify what sort of CHIPSET is in the USB/SERIAL converter, I suspect it might be an FTDI chip.  One size indeed doen't not fit all.

# dmesg | tail

Look to see what is reported when you plug the cable in.  FTDI drivers aren't compiled inot the kernel but they can be loaded manually.

# insmod ftdi_sio

Member for

16 years 5 months

BodgeIT

16 years 4 months ago

# dmesg | tail
br0: port 2(eth0) entering listening state
br0: port 1(eth1) entering listening state
br0: port 2(eth0) entering learning state
br0: port 1(eth1) entering learning state
br0: port 2(eth0) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth1) entering forwarding state
br0: topology change detected, propagating
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: USB device 2 (vend/prod 0x1a86/0x7523) is not claimed by any active driver.

I've tried loading the ftdi driver too and re-running dmesg | tail but still no good.

Hmm.. I figured it was a bit of a risk when I ordered them, they were cheap so no biggie.  What exactly should we be looking for?

Also with the HUB, I have ordered this: http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=120591099807

Do you see any issues?

Member for

16 years 10 months

brett

16 years 4 months ago

From the vend/prod string I see this is the winchiphead chipset, so it needs the CH341 driver, unfortunately this only exists in the 2.6 kernel branch - the livebox is using a 2.4 kernel.

Most people don't advertise what chipset is in their USB/Serial convertors but whenever I've bought one I've end up with a Prolific 2303 chipset which is suppport by a 2.4 kernel.  So I guess I've been lucky or you've been unlucky.  :)

If I get some time I'll backport the 2.6 kernel driver to 2.4 so these can be supported too.

This one uses the prolific chipset: (1.99 + 1 quid postage) a bargain!

http://cgi.ebay.co.uk/USB-SERIAL-RS-232-DB9-CABLE-ADAPTER-/270602783469…

I googled "nikkai prolific" and people seemed to talk about these two in the same breath so its a good bet.

Member for

16 years 5 months

BodgeIT

16 years 4 months ago

I prefer to see it as you've been luckier!

Member for

15 years 11 months

kim

15 years 11 months ago

New to this - got all the way through then found I had the wrong USB/Serial converter.  And I have got three of them!

Are there any plans to "backport to the 2.6 kernel driver" as indicated above?

Failing that is there a reliable source on ebay? - the link appears (not surprisingly) out of date.

Failing that I suppose I could buy the current cost cable - but would like to explore above options.  I would prefer

not to pay nearly as much for the cable than I did for the whole box!

Member for

15 years 11 months

kim

15 years 11 months ago

Thank you for this information and finding my post in a slightly strange place.  This looks as though it will do me fine since I have already built an interface to take the TTL signals from the Current Cost and converts it to RS232 - with a DB9 connector.  All this works into the PC but not my nice new shiny HAH kit.

Thanks also for speedy reply