A JeeNode can be flashed from the HAH system. This is in anticipation of getting these into the shop very soon now on a limited basis as our first run was to make sure there where no fabrication errors before doing a larger run of PCB's.
http://www.dbzoo.com/livebox/hah_jeenode?&#flashing_from_the_hah
Member for
16 years 10 monthsUpdate on HAH AVR flashing
I tried reflashing the latest firmware to an AVR328 with an Arduino bootloader from the HAH itself and it works just fine. I use a JeeNode as my host board to perform the flash, but an Arduino should work just as well.
I also found that if I tried to "wget" the AVR-r271.hex file directly to the HAH system it seemed to get corrupted so I had to download it to my PC first them SCP/FTP it over.
Anyway this works - just thought I'd mentioned it - you can remove the (-v) switch to make the output a little shorted if you wish.
# ./avrdude -v -C ./avrdude.conf -c arduino -p m328p -P /dev/ttyUSB0 -b 57600 -Uflash:w:AVR-r271.hex
avrdude: Version 5.10, compiled on Jul 12 2011 at 14:18:41
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2009 Joerg Wunsch
System wide configuration file is "./avrdude.conf"
User configuration file is "/root/.avrduderc"
User configuration file does not exist or is not a regular file, skipping
Using Port : /dev/ttyUSB0
Using Programmer : arduino
Overriding Baud Rate : 57600
AVR Part : ATMEGA328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 5 4 0 no 1024 4 0 3600 3600 0xff 0xff
flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : Arduino
Description : Arduino
Hardware Version: 2
Firmware Version: 1.16
Vtarget : 0.0 V
Varef : 0.0 V
Oscillator : Off
SCK period : 0.1 us
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.01s
avrdude: Device signature = 0x1e950f
avrdude: safemode: lfuse reads as 0
avrdude: safemode: hfuse reads as 0
avrdude: safemode: efuse reads as 0
avrdude: NOTE: FLASH memory has been specified, an erase cycle will be performed
To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file "AVR-r271.hex"
avrdude: input file AVR-r271.hex auto detected as Intel Hex
avrdude: writing flash (19564 bytes):
Writing | ################################################## | 100% 6.27s
avrdude: 19564 bytes of flash written
avrdude: verifying flash memory against AVR-r271.hex:
avrdude: load data flash data from input file AVR-r271.hex:
avrdude: input file AVR-r271.hex auto detected as Intel Hex
avrdude: input file AVR-r271.hex contains 19564 bytes
avrdude: reading on-chip flash data:
Reading | ################################################## | 100% 5.00s
avrdude: verifying ...
avrdude: 19564 bytes of flash verified
avrdude: safemode: lfuse reads as 0
avrdude: safemode: hfuse reads as 0
avrdude: safemode: efuse reads as 0
avrdude: safemode: Fuses OK
avrdude done. Thank you.